手机在线不卡一区二区,亚洲精品亚洲人成在线,国语自产少妇精品视频蜜桃,午夜福利av无码一区二区,最新永久无码av网址亚洲,国产成人无码激情视频,国产日韩精品视频无码,亚洲爱婷婷色婷婷五月
Welcome to the official website of Legret Metal Company
Focus on electronic welding for 20 yearsDONGGUAN LEGRET METAL.,LTD
National consultation hotline:135-2799-2739
Contact US
mobile phone: 135-2799-2739
Service hotline: 0769-38893080
Email: lzd@dglzd.com
Address: Dongguan lvzhidao Metal Co., Ltd
Contact person: Manager Zeng
Industry information

What are the characteristics of reflow welding, one of the common welding methods of electronic components?

作者:Solder manufacturer 2021-03-08 0

In the production process of electronic products, there are two common welding methods of electronic products, which are called reflow soldering and wave soldering;


The difference between the two welding methods is that the wave peak welding is mainly used to weld the plug-in circuit board, while the reflow welding is mainly used for SMT chip board welding.


Reflow welding process is to realize the soldering of mechanical and electrical connection between the welding end of surface assembly components or pins and the solder pad of printed board by remelting the paste solder which is pre distributed to the pad of printed board.


Reflow welding can control the amount of solder applied in the leading process, effectively reduce the incomplete defects of solder, such as false welding and bridge welding, so as to make the welding quality stronger, the weld joint consistency better and the reliability is very high.


During the process of electronic processing, the reflow welding does not directly dip the component into the molten solder, so the component is subject to small thermal impact (because the heating mode of reflow welding is different, in some cases, the temperature applied to the components will be higher, and the thermal stress of the corresponding components will be relatively large).


The solder for reflow welding is a commercial solder paste. It can ensure the normal composition when ordering, and it will not mix impurities in general, and it is easier to ensure the quality of welding.


If the position of solder applied on PCB is correct in the leading process and the position of the sticking component deviates from that of the component, during the reflow welding process, when all the welding ends, pins and corresponding pads of the components are wet at the same time, the effect of the surface tension of the molten solder will produce self setting effect, which can automatically correct the deviation and pull the components back to the approximate accurate position.


Local heating heat source can be used, so different welding methods can be used on the same substrate.


The process is relatively simple, and the workload of repairing electronic components is very small when the defective products appear.


主站蜘蛛池模板: 普定县| 镇原县| 湟源县| 蓬安县| 六盘水市| 霍城县| 屏山县| 定州市| 仪陇县| 曲水县| 东阳市| 麻城市| 三穗县| 运城市| 五河县| 三亚市| 波密县| 米林县| 鲁甸县| 榕江县| 偃师市| 武汉市| 广饶县| 盱眙县| 潜山县| 鄂托克前旗| 芦溪县| 兴和县| 宜宾市| 岱山县| 仲巴县| 勃利县| 佛冈县| 托克逊县| 台山市| 微博| 通化县| 五莲县| 定州市| 阜宁县| 建宁县|